0.250"

-50 to 260°C (-58 to 500°F).

Stainless steel with copper alloy tip.

2.0 seconds typical in moving water.

3.0 seconds for dual element models.

100 psi (6.9 bar).

Single element probes: 1000 megohms min. at 500 VDC, leads to case.

Dual element probes: 100 megohms min. at

100 VDC, between elements and leads to case.

Withstands 10 to 2000 Hz at 20 G’s min.

Withstands 100 G’s min. sine wave

0.250"

-184 to 260°C (-300 to 500°F).

Stainless steel with copper alloy tip.

on special order.

Typical value in moving water:

Grounded junction: 1.5 seconds.

Ungrounded junction: 7 seconds.

Pressure rating: 1

00 psi (6.9 bar).

Insulation resistance: 10 megohms min. at 100 VDC, leads to case, ungrounded junctions

only.

Withstands 10 to 2000 Hz at 20 G’s min.

Withstands 100 G’s min. sine wave

Spring-loaded holders provide a quick and simple installation of probe sensors — pull out and twist the knob, insert the probe until it bottoms out, and release the knob. Spring pressure holds the probe tip in contact with the measuring surface for faster response and more reliable measurements. Features a rubber O-ring that doesn’t crimp the probe but prevents oil leakage to 50 psi (3.4 bar) at up to 260°C.

300 series stainless steel

-40 to 260°C (-40 to 500°F)

3/4 - 14 NPT

1/2 - 14 NPT

Aluminum/silicone gasket

Dimmensions:

H - 3.5 (89)

L - 3.5 (89)

D - 2.0 (51)

CONNECTION HEAD IS SUITABLE FOR USE IN HAZARDOUS LOCATIONS AS DEFINED BY THE NATIONAL AND CANADIAN ELECTRICAL CODES AS:

• CLASS I, GROUPS B, C, AND D; CLASS II, GROUPS E, F, AND G,

• T6 (Ta = 40°C), T2 (Ta = 260°C) Ta LIMITED TO 160°C FOR CSA CLASS II

• CLASS I, ZONE 1, AEx\Ex d IIC T6 (Ta = 40°C), T2 (Ta = 260°C);

• WITH O-RING IN PLACE, THE CONNECTION HEAD IS SUITABLE FOR

  WEATHERPROOF APPLICATIONS DEFINED AS TYPE 3 AND 4.

• INGRESS PROTECTION OF IP65.

1. HOLDER IS EQUIPPED WITH A DOUBLE CONTAINMENT SYSTEM WHICH HAS TWO O-RING SEALS THAT SEAL AROUND PROBE. IF FIRST O-RING

   IS BREACHED THE FITTING WILL LEAK VIA THE WEEP HOLE. THE

   SECOND O-RING WILL KEEP MEASURED MEDIUM FROM REACHING

   ELECTRICAL COMPONENTS.

2. O-RING MATERIAL: VITON.

3. TEMPERATURE LIMIT: 260°C (500°F) MAXIMUM.

4. PRESSURE: HOLDER WILL WITHSTAND 50 PSIG AT MAXIMUM

   TEMPERATURE WITHOUT ANY LEAKS AROUND THE O-RING SEAL.

1. ELEMENT: PLATINUM.

2. TEMPERATURE LIMITS: -50°C TO 260°C (-58°F TO 500°F)

3. INSULATION RESISTANCE: 1000 MEGOHMS MINIMUM AT 500 VOLTS DC,

   LEADS TO PROBE CASE. DUAL ELEMENT ONLY: 100 MEGOHMS AT 100

   VOLTS DC, BETWEEN ELEMENTS.

4. LEADS: AWG #26, STRANDED, TFE INSULATED.

5. CASE: STAINLESS STEEL, WITH COPPER ALLOY TIP.

6. Ø.236 ±.005 [Ø6.00 ±0.13] FOR THIS LENGTH ONLY.

7. THE PD AND PA RESISTANCE THERMOMETERS WILL MEET THE

   RESISTANCE-TEMPERATURE RELATIONSHIP AND TOLERANCES

   SPECIFIED IN IEC 751, CLASS B.

8. PROBE IS SUITABLE FOR USE IN HAZARDOUS LOCATIONS DEFINED BY

   CENELEC EN 50 014 AND EN50 018, EEx d IIC T6.

1. THE ASSEMBLY IS SUITABLE FOR USE IN HAZARDOUS LOCATIONS DEFINED AS FOLLOWS:

   1. NATIONAL AND CANADIAN ELECTRICAL CODES:CLASS I, GROUPS B, C, AND D; CLASS II GROUPS E, F AND G, T6 (Ta = 40°C), T2 (Ta = 260°C), Ta LIMITED TO 160°C FOR CSA CLASS II;

   2. NATIONAL ELECTRICAL CODE (NEC 505):CLASS I, ZONE 1, AEx d IIC T6 (Ta = 40°C), T2 (Ta = 260°C);

   3. CANADIAN ELECTRICAL CODE (IEC):Ex d IIC T6 (Ta = 40°C), T2 (Ta = 260°C).

2. TEMPERATURE RANGE: -50°C TO 260°C

3. INSULATION RESISTANCE: 100 MEGOHMS MINIMUM AT 100 VOLTS DC, LEADS TO PROBE CASE.

4. THE PD RESISTANCE THERMOMETER WILL MEET THE RESISTANCE-TEMPERATURE RELATIONSHIP AND TOLERANCES SPECIFIED IN EN 60751 (IEC 751), CLASS B.

5. CONNECTION: TERMINAL BOARD FOR WIRES UP TO AWG #14.

6. ADJUSTABLE SPRING-LOADED OPTION IS EQUIPPED WITH TWO O-RING SEALS. IT HAS A WEEP HOLE BETWEEN THE PRIMARY AND SECONDARY O-RING SEALS TO INDICATE FAILURE OF THE PRIMARY SEAL.

7. THE G1/2A THREAD FORM WILL MEET THE FOLLOWING SPECIFICATION: ISO 228/1, DIN 259, BS2779 AND JIS B0202. PROCESS CONNECTION END CONFIGURATION PER DIN 3852, PART 2 TYPE A (STUB END).