|
| |
|
Accelerometer Mounting Accessories |
|
Accelerometer Mounting Accessories are provided
to assist our customers with the installation of permanently mounted
accelerometers. These accessories will simplify acquiring the various components required
to complete the job quickly and properly.
|
|
The following list itemizes the accessories that may be required for
an accelerometer installation:
|
|
Motor Fin Mounts: |
|
New CMCP-205 Motor Fin Mounts are made of 416
Stainless Steel and provide a mounting location for magnetically or permanently mounted accelerometers. Adhesive/Filler is used to mount the Fin Mounts
between the cooling fins on motors where the bearing cap is inaccessible. Four (4) sizes
are offered to retrofit most any motor. 50 and 100 unit Kits are available that come
complete with adhesive/filler and mixing nozzles. Pads are 1" Dia. (25.4 mm),
3/8" Thick (9.5 mm) and are pretapped 1/4-28 UNF with a 32 microinch RMS surface
finish. Kits are available for lots of 50 or 100 and come complete with adhesive/filler
(50 ml per 10 mounts). Denote kit by adding -50 or -100 to end of part number.
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI Part# |
Stem Size (LxW) |
|
CMCP-205- |
01 |
1.25" x 0.50" (31.75 x 12.7 mm) |
|
|
02 |
2.00 x 0.50" (50.8 x 12.7 mm) |
|
|
03 |
1.75" x 0.25" (44.5 x 6.35 mm) |
|
|
04 |
1.00 x 0.25" (25.4 x 6.35 mm) |
Optional Items:
|
STI Part# |
Description |
|
CMCP-206 |
Adhesive/Filler (50 ml) |
|
CMCP-207 |
Dispenser |
|
Accelerometer Mounting Pads: |
|
Sales
Technology's Accelerometer Mounting Pads are used for glue (epoxy)
mounting accelerometers to a prepared surface.
Mounting pads are stainless steel and are 1" (2.54 cm) in diameter and either
1/4" (0.64 cm) or 3/8" (0.95 cm) thick. The pads are lapped on one side to
provide an ideal surface for accelerometer mounting. The pads are also provided with a
1/4" x 28 UNF tapped hole for accelerometer mounting. The 1/4" thick version is recommended for low clearance
installations or when using the combination epoxy and stud mounting method. The 3/8"
thick version is recommended for installing ring mode accelerometers.
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-200- |
01 |
1" Dia.
1/4" Thick |
|
|
02 |
1" Dia.
3/8" Thick |
|
Acrylic Adhesive Bypacs: |
|
Acrylic 406/17 Adhesive Bypacs are an
easy to use solution for gluing Accelerometer Mounting Pads to a prepared
surface area on the bearing housing. The adhesive is prepared inside the
Bypac by removing the plastic separator and kneading together the two
adhesive components. A corner of the bag is then removed to allow easy
dispensing of the mixture. Each Bypac will glue one (1) Accelerometer
Mounting Pad. A Material Safety Data Sheet for this product can be
supplied on request.
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-210 |
406/17
Adhesive Bypac |
|
Silicone Dielectric: |
|
In high frequency accelerometer applications, it is recommended by
the manufacturer to apply a thin coating of Silicone Dielectric between the
accelerometer and the mounting surface before mounting the accelerometer to the proper
torque. The dielectric helps insure the transmittal of high frequency vibration across the
mounting interface. When an accelerometer is installed in harsh or moist environments,
Silicone Dielectric is also recommended for additional sealing of the accelerometer's
connector. Each one (1) ounce tube of Silicone Dielectric will install
approximately 50 to 100 accelerometers. When also used as a connector sealant, each tube
will install approximately 15 to 25 accelerometers.
|
Download Data Sheet in PDF Format
Ordering
Information:
|
STI Part# |
Description |
|
CMCP-212 |
Silicone Dielectric
1-oz. |
|
Accelerometer Mounting Studs: |
|
Accelerometer mounting studs are used to mount
1/4" thick STI Mounting Pads directly to the
tapped bearing housing in combination with epoxy. The 3/4" long stud provides the
proper length for mounting the pad to the bearing surface and in turn the accelerometer to
the stud. Allen studs are made of stainless steel and have 1/4" x 28 UNF threads.
Allen head studs are provided in packs of ten (10).
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI Part# |
Description |
|
CMCP-230 |
10 Mounting Studs |
|
Piloted End Mill Spot Reamer: |
Piloted End Mill Aircraft Spot Reamers are used to mill a 1"
(2.54 cm) smooth flat area on bearing housings. The
flat area will accept a stud mounted accelerometer or a glue (epoxy) mounted with an
STI Accelerometer Mounting Pad. A 7/32" drill, pilot, allen wrench and end mill are
included in each kit. The 7/32" drilled hole can then be tapped with a 1/4" x 28
UNF starter and bottom tap for stud mounted accelerometers.
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI Part# |
Description |
|
CMCP-701 |
Piloted End Mill Kit |
|
Indexable
Counter-bore (End Mill) Kit: |
|
Indexable Counter Bores
are used just like the less expensive spot reamer shown above to mill a 1" (2.54 cm)
smooth flat area on a bearing housing to mount an
accelerometer. Their major advantage is that the have replaceable (indexable) Titanium
Nitride cutting edge inserts. These inserts are triangular with three cutting edges per
insert. Each cutting surface is very durable allowing greater machining capability over the
less expensive spot reamer. Each kit comes complete with counter-bore, 10 ea. inserts,
pilot, insert screw and insert key.
|
Download Data Sheet in PDF Format
Ordering Information:
STI
Part# |
Description |
CMCP-710 |
Indexable Counterbore Kit |
Spare Parts:
STI
Part# |
Description |
CMCP-711 |
Titanium Nitride Inserts
(10) |
|
CMCP-712 |
7/32" x 3/16" Pilot (1) |
|
CMCP-713 |
Insert Screw (1) |
|
CMCP-714 |
Insert Key (1) |
Download Data Sheet in PDF Format
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-220- |
XX- |
XX |
Adhesive Mount Kits |
|
|
10 |
|
10 Accelerometers |
|
|
32 |
|
32 Accelerometers |
|
|
64 |
|
64 Accelerometers |
|
|
128 |
|
128 accelerometers |
|
|
|
01 |
1/4" Mounting Pads |
|
|
|
02 |
3/8" Mounting Pads |
Each of the kits provides the following quantities of
each item:
|
CMCP-220- |
10 |
32 |
64 |
128 |
|
Piloted End Mill Kits |
1 |
2 |
3 |
6 |
|
Mounting Pads |
10 |
32 |
64 |
128 |
|
Adhesive Bypacs |
10 |
32 |
64 |
128 |
|
Silicone Dielectric |
1 |
2 |
3 |
6 |
|
NEMA 4X Fiberglass Junction Boxes: |
|
NEMA 4X Fiberglass Junction Boxes are designed for both indoor and
outdoor use in highly corrosive environments such as paper machines and related
equipment. Screw covers are hinged on one side and provided with an oil resistant
"O" ring gasket. The fiberglass is easily drilled for the installation of water
resistant cable entries.
Fiberglass boxes are light grey in color and are provided with
mounting feet and stainless steel mounting screws.
|
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-260- |
01 |
6" H x 6" W x
4" D
(15.2 x 15.2 x 10.2 cm) |
|
|
02 |
8" H x 6" W x
4" D
(20.3 x 15.2 x 10.2 cm) |
|
|
03 |
10" H x 8" W x
6"D
(25.4 x 20.3 x 15.2 cm) |
|
Liquid Tight Strain Relief Connectors: |
|
Liquid Tight Strain Relief Connectors are used for making direct
accelerometer or transducer extension cable entries into the junction boxes listed
above. Long cable runs or cables other than the actual extension cable should be installed
in conduit. Connectors are constructed of Polyamide and provide both
environmental sealing and strain relief. The connectors are temperature rated to -40o
to 212o F (-60o to 100o C). The connectors have a
pressure rating of up to 150 PSIG.
|
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-261- |
XX |
Liquid Tight
Connectors |
|
|
|
Min. OD |
Max. OD |
|
|
01 |
0.08" (2mm) |
0.20" (5mm) |
|
|
02 |
0.16" (4mm) |
0.31" (8mm) |
|
|
03 |
0.20" (5mm) |
0.35" (9mm) |
|
|
04 |
0.28" (7mm) |
0.47" (12mm) |
|
|
05 |
0.35" (9mm) |
0.70" (18mm) |
|
|
06 |
0.51"(13mm) |
0.78" (20mm) |
|
Ceramic Wire Nuts: |
|
Ceramic wire nuts are recommended for paper machine applications to
connect accelerometer extension cables to the CMCP-400 20 AWG instrument
cable. The wire nuts have no metal parts and are not subject to corrosion. It is recommended that Silicone RTV be applied to the wire ends
before installation of the connector.
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-270 |
Pack of 100 |
|
Tefzel Tie Wraps: |
|
Tefzel tie wraps are recommended for all locations where high
temperatures and or harsh environments are a factor. Examples are tying
down accelerometer extension cables to paper machines and in junction boxes. Tefzel tie
wraps are rated for -50o to 302o F (-46o to 150o
C) .
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-271- |
01 |
4" Small |
|
|
02 |
7.25" Medium |
|
|
03 |
14.5" Large |
|
Spiral Wrap: |
|
Spiral Wrap is recommended for instrument wire protection where it
is subject to bending and or abrasion.
|
Download Data Sheet in PDF Format
Ordering Information:
|
STI
Part# |
Description |
|
CMCP-272- |
01 |
3/8" x 80 ft. |
|
|
02 |
1/2" x 65 ft. |
|
