|
| |
|
CMCP-OS2400
Industrial Radios |
|
 |
Features:
-
Low Cost
-
Class I, Div II
-
Secure Communication
-
Worldwide Unlicensed 2.4 GHz
-
High Power
-
Long Range with Extensive Antenna Selection
-
250 Kbps RF Data Rate
-
Ethernet and RS-485 Models
-
Configurable to Master/Repeater/Remote
|
|
The CMCP-OS2400 industrial radios combined with
our Analog to Digital
Converters and
CMCP-500 series transmitters or
CMCP-420VT vibration
transmitters provide a rugged and reliable remote monitoring solution.
Designed to operate in high-interference
environments, the radios combines advanced frequency hopping and digital signal
processing technology with outstanding receiver sensitivity and antenna
diversity resulting in exceptional noise and interference rejection.
Peer-to-peer addressing and store-and-forward repeaters allow point-to-point,
broadcast, and point-multipoint nodes. Store-and-forward repeater mode extends
network range and conserves bandwidth over the RF channel. The RF output levels
are user-configurable and 32 data channels allow multiple networks to operate in
the same area.
The CMCP-OS2400 industrial radios operate in the
license-free 2.4 GHz ISM band and can be used throughout the world with no site
licenses or monthly leased line/wireless service fees.
Operating range with the standard antenna (shown
above) is up to 1/2 mile. Several antenna options are available to increase the
range up to and beyond 16 miles.
|
Specifications:
|
General: |
|
Size |
4.50”
W x 4.12” H x 2.32” D |
|
Weight |
8
ounces |
|
Operating Temperature |
-40°C
to +75°C; -40°F to +167°F |
|
Humidity |
To
90% RH, non-condensing |
|
Antenna |
Two
SMA connectors, automatic antenna diversity |
|
Range |
Up
to 16 miles with high-gain antennas
(can be extended with repeaters) |
|
Software |
Windows®-based user setup, diagnostic software |
|
Data Interface: CMCP-OS2400-485
|
|
Serial Data Interface |
RS-485, RS-422 and RS-232 |
|
Communication |
Asynchronous half-duplex/full-duplex |
|
I/O Data Rate |
1200
bps to 115.2 Kbps full-duplex |
|
Network Topology |
Point-to-point, broadcast, point-to-multipoint, store and forward repeater,
peer-to-peer |
|
Channels |
32
user-selectable |
|
Error Detection/Correction |
32
bit CRC with automatic re-send query (ARQ) |
|
Latency |
<20
ms |
|
Encryption |
128
bit proprietary encryption |
|
Data Interface: CMCP-OS2400-ETHERNET
|
|
Ports |
10/100 BaseT |
|
Connector |
RJ-45 |
|
Compliance |
IEEE 802.3, 802.3u, 802.3x |
|
Network Topology |
Peer-to-peer |
|
Channels |
32 user-selectable |
|
Error Detection/Correction |
32 bit CRC with automatic
re-send query (ARQ) |
|
Encryption |
128 bit proprietary encryption |
|
Radio Characteristics: |
|
Frequency |
2.4-2.4835 GHz for USA; varies for other countries. Frequency hopping spread
spectrum (FHSS) |
|
Output Power |
1
mW-250 mW, programmable;
Max EIRP up to 64 W effective radiated power |
|
Channel Data Rate |
250
Kbps |
|
Receiver Sensitivity |
-100
dBm @ 5x10-4 BER typical |
|
Power: |
|
Supply Voltage |
6-24
VDC |
|
Average Power |
2.5 W
master, 1.25 W remote |
|
Regulatory Approvals: |
|
FCC |
FCC
Part 15.247 |
|
Industry Canada |
RSS
210 |
|
CE/Europe |
ETSI
300 328, ETSI 301 489, EN 60950
ATEX Pending |
|
UL |
UL
1604 Class 1 Division 2, Groups A,B,C,D Temp. Code: T4A |
|
CSA/cUL |
C22.2
No. 213-M1987 |
|
Mexico/Australia |
Approved |
Ordering Information:
|
CMCP-OS2400 |
-XXX |
One Industrial Radio with Standard Antenna |
|
|
-485 |
Supports RS-232/422/485
MODBUS RTU and ASCII
|
|
|
-ETHERNET |
Supports Ethernet - All 802.3 Protocols
|
CMCP-OS2400-485 Industrial Radio Data Sheet PDF Format
CMCP-OS2400-ETHERNET Industrial Radio Data Sheet PDF Format
|
