Navigate to the STI Vibration Monitoring Inc. homepage

Differential Expansion Transmitter/Monitor

CMCP547 Differential Expansion Transmitter/Monitor

STI
$0.00
Choose your options:
Sensor Input
Sensor Input:
Normal Direction
Normal Direction:
Alarm Module
Alarm Module:
Product Code: CMCP547
CMCP500 Transmitter Approval Label
  • Proximity Probe In
  • Differential Expansion Out
  • Transmitter or Monitor
  • DC Detection
  • Towards/Away Selectable
  • 10, 25, 50 and 200mv/mil Input
  • 4-20 mA Output
  • 2 Buffered Outputs
  • 5 Selectable Ranges
  • Fault (OK) Detection
  • DIN Rail Mount

The CMCP547 Differential Expansion Transmitters are compatible with LVDT and proximity probe inputs, they provide a 4-20 mA output proportional to the overall measurement. Each unit provides power for the associated transducer, processes the signal, and outputs a 4-20 mA dc current that is proportional to a user specified range such as 0-2 inches. Combining monitors with an existing PLC or DCS system results in a high density, low cost vibration monitoring system. With the alarm option, the unit functions as a complete single channel monitor that includes alert and danger alarms, and output relays.


Alarms relays and trip multiply are available with the Monitor version.

CMCP500 Monitor Approval LabelAlarms - The CMCP500A Series Monitors have two independent set points, with LED alarm indicators and output relay contacts (Alert and Danger). Set points are adjustable via potentiometer, from 0 to 110% of full scale. Each has an adjustable delay of 1 to 10 seconds. SPST Relay contacts are rated 5 Amps @ 30 Vdc or 250 Vac for resistive loads.

Relay contacts can be independently configured by the user for either Normally Open (NO) (Standard) or Normally Closed (NC) operation. Relays are normally de-energized and can be configured for latching or non-latching (standard) operation. Latched alarms may be reset locally or by remote contact closure.

Trip Multiply - The monitors have set point multiplication of 3X via contact closure (2X available). To avoid tripping the alarms during machine start-up.

Custom Input and Output Calibrations are Available on Request.

Buffered Output:
A BNC connector mounted on the front of the unit provides access to the buffered transducer output signal. This includes both the unfiltered vibration signal, and the DC bias voltage. Portable test equipment or analyzers like SKF-CM's MicrologTM can be connected to this output without disturbing other system outputs.

Fault Detection:
On board fault detection circuitry continuously monitors the transducer for normal operation. If a fault occurs, the output current is reduced to 2 mA to indicate the fault to the readout system. A red LED on the front of the unit is turned on to provide a local indication of the fault. Alarms:This monitoring option adds two independent set points, with LED alarm indicators and output relay contacts (Alert and Danger). Set points are adjustable via potentiometer, from 0 to 110% of full scale. Each has an adjustable delay of 1 to 10 seconds. Relay contacts can be independently configured by the user for either Normally Open (NO) (Standard) or Normally Closed (NC) operation. Relays are normally de-energized and can be configured for latching or non-latching (standard) operation. Latched alarms may be reset locally or by remote contact closure. SPST Relay contacts are rated 5 Amps @ 30 Vdc or 250 Vac for resistive loads. The Alarm option also provides set point multiplication of 3X via contact closure (2X available).

Documents Available:


Electrical Specifications:
Input: Eddy Probe or Proximity Probe Systems (10, 20, 30 50, 100, 200 mv/mil)
Power: +24 Vdc @ 45 mA max. (30 mA typical).
Protection: Reverse polarity and transient protection included.
Frequency Response: DC
Buffered Output: BNC Connector 0-20 kHz.
Accuracy: 0.5 % of Full Scale Range.
Output: 4-20 mA proportional to the full scale range.
Maximum Load: 600 Ohms Resistive.
Case: Isolated.
Range: English, 0-80 mils (40-0-40) or
Metric, 0-2 mm (1.0-0-1.0)
Direction: Jumper selectable "Towards" or "Away" from sensor.
Fault Indication: Green LED and 4-20 mA < 2mA

Relay Module:
Alarms: OK, Alert and Danger
Alarm Setpoints: Alert and Danger Adjustable 0 to 110% FS.
Trip Multiply: 2X or 3X on Contact Closure.
Alarm Relays: OK, Alert and Danger.
Form C, SPDT, 5A @ 30 VDC or 250 VAC.
Latching or Non-latching, Selectable.
Time Delay: 0.1, 1, 3, 6 or 10 Seconds, Selectable.
Alarm LED's: Alert = Yellow, Danger = Red.
Display Outputs: 0-5 VDC for Current Value, Alert Setpoint and Danger Setpoint.

Environmental Specifications:
Operating Temp.: -20°C to +80° C (-4° F to +176° F).
Storage Temp.: -55°C to +125° C (-67° F to +257° F).
Relative Humidity: 0 - 95% Non-Condensing.

Physical:
Mounting: 32 mm (G style) or 35 mm (T style) DIN Rail.
Size: Transmitter 1.0" Wide x 3.11" High x 3.95" Deep
w/Relay Module 1.6" Wide x 3.11" High x 3.95" Deep

Get access to the latest deals and more!